DIY Floating Shelves

I am so excited to FINALLY share this project with you all! I have been working on it for what feels like forever. Wait…you mean…having a baby will drastically change the amount of time in the day you have to accomplish things?!?! Case in point, I’ve been trying to write this blog post for 3 days now 🙂

When I started placing the furniture in the nursery, I knew I wanted this corner to be the “play” corner or the area for all the toys. Landon already owns quite a few books so a book shelf seemed like the way to go but I also wanted room for some sort of toy box (a post on that to come in the future) so shelves up on the wall were necessary for space. Enter the DIY Floating Shelves from Shanty 2 Chic. If you haven’t checked out their site before and you enjoy DIY building, check them out. If you’ve ever searched for DIY building projects on Pinterest, chances are you’ve come across some of their work. Their projects are always really well explained and the plans are very detailed.

I did make some adjustments to the original plans because the plans called shelves that were 3.5′ in either direction and I only had room for 2′. So, my plans are for 2′ long corner shelves and the materials listed are enough for 3 shelves. If you follow the plans on Shanty 2 Chic, their plans are for 3.5′ shelves and the materials listed are for 1 shelf so make sure you double or triple the amount of wood depending on how many shelves you want.

So, here we go…step by step 🙂

Supplies
NOTE: Before purchasing the wood, see the note in step 6 regarding the 2×4 and 1×6 boards
3 – 2″ x 4″ x 8′
2 – 1/4″ x 24″ x 48″ plywood
2 – 1″ x 10″ x 8′
2 – 1″ x 6″ x 8′
kreg jig for pocket holes
drill
2 1/2″ pocket screws
nail gun
1 1/4″ brad nails
3″ screws (torx or dry wall, whatever you prefer, these will be to screws the support boards to the wall and into a stud)
stud finder
wood glue
paint
hardware (for decorative purposes, I’ll show you what I used when I get to that part below)

Step 1: You will need to determine the height placement of each shelf. You want to think about what you are going to put on the shelves and how much space you need in between each one. I wanted my shelves to take up the majority of the corner and knew I was going to be putting some taller items and books on them so here are the measurements I used…
Floor to ceiling, the room is 96″ tall. Each shelf is approximately 4.5″ tall. Based on that, I measured out equal spacing from ceiling to the top shelf, between each shelf, and from bottom shelf to the floor, which was 20.5″.
Ceiling
20.5″
Shelf #1: 4.5″
20.5″
Shelf #2: 4.5″
20.5″
Shelf #3: 4.5″
20.5″
Floor

You will also want to locate the studs in your wall and mark those as well as you will drill each wall cleat directly into a stud.

Step 2: Build your wall cleats.
Using the 2″ x 4″ x 8′, make the following cuts
3 pieces @ 2′ (long wall cleat)
3 pieces @ 1′ 10 1/2″ (short wall cleat)
12 pieces @ 7 5/8″ (cleat braces)

When constructing each wall cleat, you will use one long wall cleat, one short wall cleat and 4 cleat braces, 2 1/2″ pocket screws and wood glue.
Using a kreg jig, drill for 2 1/2″ pocket screws into one end of each cleat brace then attach the cleat braces to the cleats as shown. I didn’t measure the placement of the cleat braces, just lined up the wall cleats (long wall cleat against the corner, short wall cleat against the long wall cleat) and then marked where the cleat braces should go so that they just met each other at the corner edge. The other two cleat braces went at the opposite ends of the wall cleats.

Step 3: Attach wall cleats to the wall
Use a drill bit that is slightly smaller than the 3″ screws. Line up a wall cleat where you want it and drill a pilot hold into the wall cleat directly over the stud, check for level. Using the 3″ screws, attach the wall cleat to the wall in at least 2 different points.

Step 4: Attach bottom panels to braces
You are basically going to wrap the braces in wood to build out your shelf. Using the 1/4″ plywood, make the following cuts (I made the cuts at home but if you don’t have a saw, you can ask some in the lumber department to make the cuts for you)
3 pieces @ 23 1/4″ x 9 1/4″ (long bottom panel)
3 pieces @ 14″ x 9 1/4″ (short bottom panel)
Use a wood glue, a nail gun and 1/4″ brad nails to attach 1 long bottom panel and 1 short bottom panel to each set of braces.

Step 5: Attach top panel to braces
Using the 1″ x 10″ x 8′ make the following cuts
3 pieces @ 23 1/4″ (long top panel)
3 pieces @ 14″ (short top panel)
Attach 1 long top panel and 1 short top panel to each set of braces using wood glue, 1 1/4″ finish nails and a nail gun.

Step 6: Attach the side trim
Using the 1″ x 6″ x 8′ make the following cuts
6 pieces @ 4 1/2″ x 9 1/4″ (side front trim)
NOTE: Because 2×4 are used for the wall cleats, it requires the front and side trim to be only 4 1/2″ wide which is not a width you can buy and will have to rip the board down to 4 1/2″. Again, you can have them do it for you in the lumber department. If you have a table saw at home then you can do it yourself. The other option would be to use 2″ x 3″ for the walls cleats instead of 2″ x 4″. By using 2″ x 3″, you will not need to alter the width of the 1″ x 6″ boards.
Attach side front trim pieces using the same method, wood glue, a nail gun and 1 1/4″ finish nails.

Step 7: Attach front trim pieces
Using the remaining 1″ x 6″ x 8′ boards, make the following cuts
3 pieces @ 14 3/4″ x 4 1/2″
3 pieces @ 14″ x 4 1/2″
Attach using the same method, wood glue, a nail gun and 1 1/4″ finish nails

Step 8: Finish with paint and decorate!
I used wood filler to fill in nail holes and the seams. Once dried, I went over the wood filler with 180 grit sand paper to smooth it out.

I used Heirloom Traditions chalk paint in A La Mode to finish the shelves, topped with clear wax, and sanded the edges for a roughed up look.

Finally, I added some hardware to the corners to give the shelves a bit of an industrial look to compliment some of the other pieces in the nursery.

I used metal corner braces similar to these from Lowes, and furniture tacks to attach them, spray painted all the pieces with black matte finish spray paint and roughed them up with some sand paper before attaching.

That’s that! Then I decorated 🙂