DIY Flower Basket Stand

IMG_5712.JPG

Happy belated Mother’s Day to all the amazing, hard-working mamas out there! I hope you all enjoyed a day of relaxation, pampering and spending quality time with your kiddos.

I started this project as something completely different…I was searching for DIY floor lamp ideas and came across a flower pot stand idea on Pinterest instead. My goal was to make it and post the instructions in time for you all to make it yourself, possibly for a Mother’s Day gift, however, my morning sickness got in the way 😦

I’m at 16 weeks now and my mornings are getting more and more difficult by the day. I wake up every single morning with a headache that has been lasting about 2 hours before I get rid of it enough to function and for the last couple days, intense joint pain in my hips is actually waking me up early in the morning. Anyone else have this? I feel like it’s so early to be having hip/joint pain already. My hope is that I just pushed myself a bit too hard with all the retail chaos of Mother’s Day shopping. I was running around quite a bit more than usual from Friday-Sunday. I used my pregnancy pillow last night and for the first time, woke up today without a headache! Woohoo!! (This could also be because I ate a very late dinner) However, the pillow did nothing for the joint pain. Let’s hope taking it easy for few days will help.

So this flower basket stand was super easy, it’s made out of an old floor lamp and a metal hanging basket. And other than dry time for the spray paint, I think the whole thing took me an hour to put together!

Supplies
old floor lamp
drill and drill bits
block of 1×6″ scrap wood
1″ self drilling screws
20″ metal hanging basket with fiber liner (remove hanging chains from basket)
a few inches 1/2″ copper plated steel tab tape
3/4″ self drilling screws
spray paint in color of your choice
potting soil and plants of your choice

Step 1:
I started with this lamp that I got for $20 at a thrift store

IMG_5684.JPG
Step 2:
Remove the glass bowl, light bulb and electrical fixture from the lamp. (The electrical fixture should come out by unscrewing it from the base and you’ll be able to pull a bit of the cord out throught the top of the lamp). Using wire cutters, cut the electrical cord away from the electrical fixture. You should now be able to pull the electrical cord from the  bottom of the lamp until it is completly removed.

IMG_5687

Step 3:
Using a drill and a drill bit just slightly larger than the threaded post of your screws, you will drill a hole on 4 sides at the top of the lamp post, holes should be evenly spaced apart. (Note: the larger hole is from the lamp switch, not from drilling)

IMG_5697

Step 4:
Using a piece of scrap wood (mine was a piece of 1×6 board but to about 8″), turn the lamp post upside down and center it on the scrap wood. Attach the lamp post to the wood using 1″ self drilling screws. You may want a helper for this step as the lamp post may not sit evenly and stay upright while you are drilling.

IMG_5700

Step 5:
Using the copper plated steel tab tape, you will attach the wire hanging basket to the wood. Turn the post back over so it is standing upright, scrap wood facing up. Set the wire basket on top of the wood, centered. Cut a piece of tab tape long enough to weave through some of the basket wires and still attached the tab tape to the wood with 3/4″ self drilling screws. As you are attaching the tab tape, you should be pulling it or holding it down tightly so the basket is secure and not loose enough to move.

IMG_5701

Step 6:
Use your spray paint to paint the lamp base, wood and hardware in your desired color and allow to dry according to directions on the can. Once dried, add the fiber liner to the metal basket.

 IMG_5703

Step 7:
Plant your basket!! Again, be aware that your basket stand may be top heavy. Mine was a bit unsteady so I was very careful when planting and because it was so tall (mine stands about 7 feet tall without plants), I had to plant it while standing  a few stairs above the stand. I was also worried about the stand blowing over in the wind so I used wired to attach the stand to a post on my deck to hold it in place.

IMG_5711

I used an ornamental grass, 3 geraniums and 3 bacopa plants to dress up my basket, as well as an outdoor flat black spray paint on the base. I love this planter so much, I think I’m going to make a few others to match it!

IMG_5717

Advertisements

One thought on “DIY Flower Basket Stand

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s